Patch up wall

A joint compound can be painted on top before it dries out to make the surface smooth again. If the hole is larger than an inch, then cut it out. You will need a new piece of drywall material that is twice the size of the hole. Be sure to measure and cut properly; otherwise, you will have unnecessary gaps in the repair work. Cut a square around the damaged area and saw off any protruding corners or edges.

Clean the sawdust off using a brush and apply joint compound on the area where you will place the patch. Place drywall tape over the top and firmly press to smooth out any bubbles or bumps. After it has dried, use sandpaper to make it even with the wall surface. Holes larger than 10 to 12 inches need to be repaired using mesh tape. Cut out the damaged area and clean out all of the sawdust off. If the hole has jagged edges, use sandpaper to smooth them down before applying joint compound.

Cut a piece of mesh tape with an inch more on each side than what is needed for filling in the patch. Apply joint compound on the mesh tape and smooth it out with a taping knife. Place the mesh tape over the hole and make any adjustments if needed. Dust off any excess joint compound from your work area before it dries up. Call in a professional if you run out of materials or do not have enough time to complete this project. This happens when the drywall studs have been secured too tightly into the wall.

The nails will be slightly raised from the surface and require a little attention to make them completely flush with the wall. Use a flathead screwdriver to press down on the nail head, making sure it is pushed in. Leave it there for at least twenty minutes or until you see that the nail head has sunk further. Punching drywall nails causes damage that is much more difficult to repair.

Once you remove the screwdriver, use a hammer to firmly tap on the top of the nail until it is pressed completely flush with the wall. It usually takes more force than usual, but be careful not to hit too hard. If you mistakenly damaged the corners of your passage or doorway or want to cover up any damaged areas of your drywall, you can use a corner bead.

It is a series of metal profiles used on interior corners for durability and easy installation. When the pop-outs happen in the corner, take out all the broken pieces and clean off any dust or debris. Apply joint compound on the entire area to become smooth before applying filler.

Once the compound dries out, sand it down with sandpaper to make it even with the rest of the wall. Cut a piece of corner bead at least 4 inches long and attach it to the corner using drywall screws.

Secure it into place using your screwdriver while aligning the profile to the corner wall. Drill two holes along each side of the corner and one in the middle. Patching textured wall requires a bit of extra work to finish. After patching, take four parts of compound and 1 part of water, mix it well and dip a stiff brush into the mixture. Sprinkle the mixture on the wall with gloved fingers and fix the texture using the brush. Once it is properly set, use sandpaper to smooth out any jagged edges.

Textured walls are not for rough treatment and sometimes require more attention than regular drywall. If you happen to make a mistake while patching, do not panic because there are still ways that you can repair it. Just make sure to clean up any dirt or dust you might have caused when patching. This is the most crucial part of patching and repairing drywall. After the drywall is fixed, you might see some uneven areas that need to be sanded down before painting.

Use a fine grain of sandpaper and smooth out the entire wall until it becomes completely even with all of your tools and materials properly put away. Check if all nails, screws, and any other hardware are in place, and then give the wall a light coating of primer before you apply paint.

This will help hide any lines and accentuate your work with some color. Drywall is one of the most durable building materials that have been used for decades. Trim hole with utility knife.

Remove anything that sticks out of hole and is loose. Sand lightly around patch, then wipe over with a rag dampened with methylated spirits. Pull backing paper off patch and adhere to wall to cover hole. Fill over patch with a thin coat of multi-purpose joint compound about the size of the trowel. Make this as smooth as possible, feathering out to edges, in order to keep sanding down to a minimum. Once dry, use sandpaper to lightly run over filled area to remove any bumps and ridges.

Wipe clean, then apply second coat of joint compound, but this time about to mm beyond compound already there. When you have a large hole in your wall, it's easy to patch it up so you can paint over it. Use a wall repair patch to easily cover up holes up to 6 in 15 cm in diameter. Cut larger holes into a square or rectangle, then create a patch out of drywall and attach it to the inside of the hole. Cover up either type of patch with joint compound and sand it to blend it into the surrounding wall.

Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow.

Download Article Explore this Article methods. Things You'll Need. Related Articles. Method 1. All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc.

Cut away and remove any loose debris and jagged paper edges from the hole. Pull off any dangling pieces of drywall and plaster. Use a utility knife to cut along the edges and remove any jagged pieces of drywall paper. This method works for holes that are up to about 6 in 15 cm in diameter.

Wall patches come in sizes up to 7—8 in 18—20 cm in diameter, and the patch needs to be slightly bigger than the hole to adhere to the wall around it. Create a repair patch that is about 1 in 2. Use sharp scissors to cut a wall repair patch so that it is approximately 1 in 2. This will allow it to adhere firmly to the intact wall surrounding the hole.

Wall repair patches are made of a mesh material that is able to support spackling on top of it. Peel the backing off the patch and stick it over the hole. Remove the lining from the adhesive on the back of the patch. Center it over the hole and press down firmly around all the sides to stick it to the wall.

Apply a thin layer of joint compound to completely cover the patch. Overlap the coat onto the surrounding wall by about 1 in 2. Tip : Joint compound is also known as drywall mud or just mud.